Shelly Motion 2 WiFi Motion Sensor with Built-in Batter

Product Information

If you choose to use the Device with the Shelly Cloud mobile application and Shelly Cloud service, instructions on how to connect the Device to the Cloud and control it through the Shelly App can be found in the Shelly Smart Control Guide. If you think your Shelly devices are working correctly and don’t want to change your network/configuration, you can ignore the repair issue. Still, you must know you are giving up the best experience of using first-generation Shelly devices with Home Assistant.

Enable to configure Shelly Device to create a Wi-Fi AP and you can connect to its network. Can also set it to be an open network. Restrict login If Home Assistant is running as a virtual machine or service on an operating system other than Home Assistant OS, you should open UDP port 5683 on the device’s firewall and/or ensure that communication from this port is redirected to the Home Assistant service. This document contains important technical and safety information about the device, its safety use and installation.Home Assistant will display a repair issue for the Shelly device if push updates from this device do not reach the Home Assistant server.

Below the Main Controls heading, observe the current room temperature, Shelly Device battery as a percentage, and light status of the room. Shelly® devices can be accessed, controlled and monitored remotely from any place where the User has internet connectivity, as long as the devices are connected to a Wi-Fi router and the Internet.Blind time: Select a blind time in minutes (from 1 to 10) after last detected motion. Select a blind time from the dropdown menu. Shelly generation 2 devices running firmware 0.12 or later can act as a Bluetooth proxy for advertisements. Active or passive listening can be enabled in the options flow. Options Change the current device name. This will reflect on the Shelly Device name in the application if the “Sync name” application setting is enabled. Factory Reset

For battery-powered devices, the update platform entities only inform about the availability of firmware updates but are not able to trigger the update process. Commerce (petits immeubles de bureaux, petits commerces de détail/restaurants/stations-service, etc.) Sleep time pauses the motion detection of the device. While this mode is active, the motion detection sensor will flash green but will not send notifications and will not perform actions. To choose the duration of the time your device will be in sleep mode, type in the number of seconds (maximum 86400) in the text box. the motion detection sensor will flash green but will not send notifications and will not perform actions. TEMPERATURE UNITS All of that is probably due to the big 6500 mAh rechargeable battery that the Shelly Motion 2 is having. This battery can last up to 3 years in standby mode and up to 1 year and a half with 6 hours usage per day.ATTENTION! Before beginning the installation, please read carefully and entirely this guide and any other documents accompanying the device. Failure to follow the installation procedures could lead to malfunction, danger to your health and life, violation of the law or refusal of legal and/or commercial guarantee (if any). Shelly Europe Ltd is not responsible for any loss or damage in case of incorrect installation or improper operation of this device due to failure of following the user and safety instructions in this guide. Introduction to Shelly® Observe the room temperature chart at the bottom of this tab, which display the temperatures measured in the last 24 hours. Below the temperature chart, observe whether or not motion has been detected by the Shelly Device. If Shelly devices are in a different subnet than the Home Assistant server, you should ensure communication on UDP port 5683 between these subnets.

By default, Shelly Motion 2 detects motion in any illumination condition. From this setting, you can change the motion detection illumination condition from the drop down menu. The options are for motion detection to be activated only when the illumination condition is: ANY(default), DARK, TWILIGHT, BRIGHT. TAMPER ALARM SENSITIVITY Set the motion detection threshold (from 1 to 256) using the slider. A lower value sets higher sensitivity. See motion detection percentage above of the slider as you move it. The first will allow specifying a temperature, the second instead of a percentage of the valve position. The integration offers device services which can be triggered by a configuration button. OTA firmware update If only the device name is set, and the device has multiple channels, the channel number will be appended to the entity name (e.g., Channel 2).

Welcome

Shelly Motion 2 (the Device) is a high-sensitivity, ultra-low power consumption Wi-Fi motion sensor, which also features light and temperature metering. The built-in light and temperature sensors provide additional opportunities for home or office automation. Shelly Motion 2 also has an integrated accelerometer for tamper protection and features vibration detection. The built-in 6500 mAh rechargeable Li-ion battery allows the Device to stay connected to the Internet in standby mode for up to 3 years, and in active transmission (approx. 6 hours/day motion detection) estimated between 12 and 18 months without recharging. Main applications The red charging indicator above to the charging port will be on while the Device is charging. The indicator will go off when the battery is fully charged. Using the homeassistant.update_entity service for an entity belonging to a battery-powered device is not possible because most of the time these devices are sleeping (are offline). Green brief flash: Unreported motion detection (the Device is not connected, or motion detection is disabled).